Новый Leadshine замкнутый контур сервопривод hbs507 3 фазы Серводвигатель 573HBM20 1000 с 1000 линия энкодера hbs57

Новый Leadshine замкнутый контур сервопривод hbs507 3 фазы Серводвигатель 573HBM20 1000 с 1000 линия энкодера hbs57
  • Продавецde-hypotheekcalculator.info
  • Список ценUS $135.00piece
  • Продажная ценаUS $135.00piece
  • ДоставкаБесплатная доставка
  • Рейтинги3,8 (643)

Oписание продукта

Notice:           

We only supply genuine Leadshine servo motor drive with reasonable price, if your budget is limit, please contact our service man online and he she will recommend you the low price other supplier.

 

HBS57 Easy Servo Drive 

 

 

Same as brushless servo systems, a HBS57 servo drive can take encoder feedback from driven easy servo motors and close the position loop to eliminate possibility of lose of movement synchronization. Therefore, stall and loss of steps commonly seen in open-loop stepper systems will never occur in HBS57 driven easy servo systems. Compared with constant output current in open loop stepper drive, output current from a HBS57 servo drive to the driven motor is load based. When torque requirement is low, the output current is automatically lowered to "just enough". But when the torque requirement is high, HBS57 can boost the output current up to 8.0A. This can significantly lower down motor heating by up to 50% over open-loop stepper systems. There is no torque reservation needed for an HBS57 driven easy servo system. You can always implement 100% of the driven stepper motor and thus improve system high speed performance by as much as 30% over open lop stepper systems. Smoothness, quietness (50% improvement), and acceleration (30% improvement) are also significantly improved in HBS57 easy servo systems.
 
Compared with traditional brushless servo systems, cost of HBS57 easy servo systems is much lower. They outperforms traditional brushless servo systems with the feature of much higher low-middle speed torque, high stiffness, quicker response time, no position hunting, no tuning / easy setup, no overshooting, and zero settling time.
Features:
32-bit DSP based vector control algorithm to combine advantage of open-loop stepper brushless servo drives
Step/Direction or CW/CCW command input
Default maximum 200K frequency; 500K optional
Input voltage: 20-50 VDC
Load-based automatically adjusted output current of 0-8.0A 
Default 4,000 (1/20) microstepping resolution; 200-104,000 (increase by 200) software configurable
No Stall and no loss of step. Closed loop between the drive and driven motor to eliminate loss of move synchronization in open loop stepper systems. 
Smooth motor movement; extra low motor heating
Fast response, no delay and zero settling time
High torque at starting and low-middle speed; high stiffness at standstill
No tuning for easy configuration over traditional servo systems
No overshooting; no hunting over traditional servo systems
Much lower cost than traditional servo systems
 
Specifications
Model:HBS57
Phase:3
Control Mode:Step & Direction
Max Input Frequency:200KHz
Encoder Feedback:Yes. Fully close the loop between the drive and drive motor
Input Voltage Range:20 - 50 VDC
Peak Current:8.00 A
Software Cofig Resolution Range:200 - 102,400 (increased by 200)
Default Step Resolution:4000
Default Holding Current Percentage:40 %
Communication Type:RS232
Pulse enabled at:Rising edge
Isolation Resistance:500M Ohm
Environment:Avoid dust, oil fog and corrosive gases
Ambient Temporature:0-50°C
Humidity:40–95% RH
Operating Temporature:0-70°C
Vibration:5.9 m/s2 Max
Storage Temporature:-20-65°C
Specification:4.57 X 2.72 X 1.04 Inches
Weight:0.62 lb
 
Electrical Specifications (Tj = 25oC/77oF):
aeProduct.getSubject()
 
 
 
 
Mechanical Specifications (unit: mm[inch] ):
aeProduct.getSubject()
 
 
Typical Connection
aeProduct.getSubject()
 
 
Capable of driving  motors:
aeProduct.getSubject()
 
 
Real Photo
 
 
aeProduct.getSubject()